Operating principle of a bourdon tube. Bourdon tube: in detail in simple language. Is this explanation correct?

Practical work

Goal of the work: study of spring pressure gauges of the OBM type (device, principle of operation, operation).

Spring pressure gauge type OBM

Manometer (from the Greek manos - rare, loose and metreo - measure) - a device for measuring excess pressure (pressure above atmospheric) of vapors, gases or liquids enclosed in a closed space. A type of pressure gauge is a vacuum gauge - a device for measuring pressure close to zero and a pressure-vacuum gauge - a device for measuring vacuum and excess pressure.

The most popular among consumers are pressure gauges with a Bourdon tube or deformation pressure gauges, the design of which was invented by E. Bourdon in 1849.

The Bourdon tube is the main structural element of the pressure gauge, its sensitive element, which is the primary pressure transducer.

The Bourdon tube is usually made of brass or phosphor bronze, has a semicircular shape for low pressures, and a coil shape for medium and high pressures. One end of the tube is connected to the inlet fitting of the pressure gauge, which is the connecting element to the medium being measured, and the other end is sealed and located in a cantilever. By using tubes of a more complex shape (spiral, helical), it is possible to obtain devices with greater sensitivity, but a smaller measurement limit.

Operating principle of deformation pressure gauges.

Under the pressure of the medium, the cantilevered end of the Bourdon tube moves - the tube tries to straighten. The magnitude of this movement is proportional to the magnitude of the pressure.

A simple gear-lever drives a pointer that indicates the pressure value on the instrument scale. Most pressure gauges of the domestic brands MP, MTP, DM TM, M 3/1, OBM, MTI, MPTI, MO, German pressure gauges Wika 111.10, 111.12, 213.53, RCh, RСhg, RChgG and pressure gauges from other manufacturers have such a device.

A general view of the OBM type spring pressure gauge is shown in Fig. 1.

Figure 1 – Spring pressure gauge type OBM

Figure 2 - Diagram of a pressure gauge with a Bourdon tube

1-Bourdon tube, 2-rod transmission mechanism, 3-tooth sector, 4-pointer, 5-fitting

Tubular springs are used as sensitive elements in pressure gauges. As can be seen from Fig. 3, one end of the tubular spring 3 goes into the fitting 7 for receiving the measured pressure. Under the influence of pressure, the free end of the pressure tube 5 will be deformed (bent), and the amount of elastic deformation is proportional to the measured pressure. Due to this relationship, measuring needle 1, due to the movement of the kinematic unit (tribe 2 - sector 4 - driver 6), shows the true value of the measured pressure relative to the instrument scale.

Figure 3 – Kinematic diagram of a pressure gauge with a Bourdon tube

1-arrow, 2-tube, 3-spring, 4-tooth sector, 5-pressure sensor (manometric tube), 6-lead, 7-fitting

Spring indicating and recording pressure gauges are repaired by the repair services of the metrology department. To do this, in a special area, workplaces must be equipped with backup glasses of a standard range with a diameter of 60, 100, 160 and 250 mm, standard scales, and special pullers for removing measuring needles from the instrument axes; clamps for fastening parts of pressure gauges, a set of ladders for restoring clogged threads of fittings M 20X1.4, devices for drawing scales, sets of tweezers and watch magnifiers, sets of small gas burners for soldering sensitive elements (springs).

The most labor-intensive operations are replacing the sensitive element (tube) of the pressure gauge and adjusting the kinematic link “sector - tube” (see Fig. 3).

The sensing element of the device is replaced after it is used to measure pressure exceeding the maximum. As a result, the tube stretches, causing residual deformation that cannot be repaired. To repair such a device, it is completely disassembled, the fitting 7 secure in a vice and dismantle the tube using a gas torch 5 from the board. After the solder has melted, the faulty tube is removed with pliers, and in its place, after cleaning the surface, a similar gauge spring is installed (at a given pressure measurement limit). The soldering area is treated with a solvent - rosin with acetone (alcohol) or hydrochloric acid.

Pressure is measured using a sensitive element - a Bourdon tube, diaphragm, liquid column, strain gauge, etc. The most common pressure measuring instruments are:

U-tube
Spring pressure gauge based on a Bourdon tube
Diaphragm pressure gauge
Diaphragm pressure sensor
Strain gauge pressure sensor
Bellows pressure sensor
Piezo-electric pressure sensor

Let's consider the principle of operation of different types of pressure gauges.

How does a spring pressure gauge work?

The sensitive element of spring pressure gauges is a Bourdon tube - a hollow brass tube of elliptical or oval cross-section, bent in an arc and sealed at one end. The other end of the tube is connected to the pressure gauge fitting, thus the internal cavity of the tube communicates with the area in which the pressure is measured.

Pressure acts on the inner surface of the Bourdon tube. Due to the difference in areas affected by the pressure of the medium, the tube will tend to straighten. It turns out that when the pressure increases, the brass tube unbends, and when it decreases, it bends. This leads to movement of the sealed end of the tube, which is connected through a rod to a gear sector acting on the arrow gear. Using a scale printed on the device, the position of the arrow is interpreted into the value of the excess pressure reading.

Pressure gauges based on a Bourdon tube are capable of measuring pressure up to hundreds of MPa, and are widely used in hydraulic drives, pneumatic drives, and water supply heating systems.

Why is the pressure gauge filled with glycerin?

To reduce vibrations and vibrations, in the presence of pulsations and sudden changes in pressure, the pressure gauge is filled with a damping liquid - glycerin, and pressure is supplied to the sensitive element through.

What is a reference pressure gauge

Reference pressure gauge- a device for measuring pressure with high accuracy, it is intended for testing, calibrating, checking, calibrating other pressure gauges or pressure sensors, for measuring precise pressure measurements, for example, when conducting research experiments, calibrating, checking other pressure gauges.

Standard pressure gauges usually have additional adjustment and adjustment devices, for example, the possibility of temperature adjustment may be provided. High demands are placed on the mechanisms of exemplary pressure gauges; they are manufactured with high precision.

Exemplary pressure gauges display pressure with high accuracy, and the scale diameter of these pressure gauges is larger than that of conventional instruments. The diameter of standard pressure gauges with 0.4 is 160 mm, and with an accuracy class of 0.15 or 0.25 - 250 mm.

How does a diaphragm pressure gauge work?

As a sensing element, a diaphragm pressure gauge uses a membrane that acts on a mechanism connected to a pointer. The measured pressure supplied to the pressure gauge deforms the membrane, which in turn causes the needle to move.

The measuring range of a diaphragm pressure gauge depends on the stiffness and area of the membrane.

Diaphragm pressure gauges are suitable for working with aggressive media; they are used to measure pressure in:

Cement and concrete pumps
Wastewater transport systems
At coke production

Pressure gauge parameters

When choosing pressure gauges, the following parameters should be taken into account:

Medium in which pressure is measured
Application area
Pressure gauge accuracy class
Diameter, according to GOST 2405-88. "Pressure gauges, vacuum gauges, pressure and vacuum gauges" produces pressure gauges with a diameter of 40, 50, 63, 100, 160, 250 millimeters
Measurement limit
- MPa, Bar, Kgs/cm 2
Housing material
Flange presence
Connecting thread of the fitting
Fitting location - radial or axial

The pressure gauge can have several scales on it to measure pressure in different units.

The presented pressure gauge has scales for measuring pressure in MPa and psi. The device shows a pressure of 250 Bar or 3500 psi.

Symbol for pressure gauges

The device designation indicates:

Functional purpose of the device
- DM - pressure gauge;
- DV - vacuum gauge;
- YES - vacuum pressure gauge;
- DT - draft gauge;
- DN - pressure gauge;
- DG - thrust gauge.
Serial or serial number of the pressure gauge
Measured pressure value
Units
Accuracy class

For example, for a pressure gauge with serial number 0001, limit 100, unit of measure MPa, accuracy class 1, the designation will look like:

DM 0001-100 MPa-1

Manufacturers of pressure gauges can set their own marking rules, however, the designation principle and the main parameters indicated in the code remain similar to those shown in the example.

Pressure gauge(from the Greek manos - rare, loose and metreo - measure) - a device for measuring excess pressure (pressure above atmospheric) of vapors, gases or liquids enclosed in a confined space. A type of pressure gauge is vacuum gauge– a device for measuring pressure close to zero and pressure-vacuum gauge device for measuring vacuum and excess pressure.

The most popular among consumers are Bourdon tube pressure gauges or deformation pressure gauges, the design of which was invented by E. Bourdon in 1849.
Bourdon tube – the main structural element of the pressure gauge, its sensitive element, which is the primary pressure transducer.
Bourdon tube It is usually made of brass or phosphor bronze, has a semicircular shape for low pressures, and a coil shape for medium and high pressures. One end of the tube is connected to the inlet fitting of the pressure gauge, which is the connecting element to the medium being measured, and the other end is sealed and located in a cantilever. By using tubes of a more complex shape (spiral, helical), it is possible to obtain devices with greater sensitivity, but a smaller measurement limit.

Operating principle of deformation pressure gauges.

Under the pressure of the medium, the cantilevered end of the Bourdon tube moves - the tube tries to straighten. The magnitude of this movement is proportional to the magnitude of the pressure.
A simple gear-lever drives a pointer that indicates the pressure value on the instrument scale. Most pressure gauges of the domestic brands MP, MTP, DM TM, M 3/1, OBM, MTI, MPTI, MO, German pressure gauges Wika 111.10, 111.12, 213.53, RCh, RСhg, RChgG and pressure gauges from other manufacturers have such a device.

Diagram of a pressure gauge with a Bourdon tube

1-Bourdon tube, 2-rod transmission mechanism, 3-tooth sector, 4-pointer, 5-fitting

In addition to pointer pressure gauges, scaleless pressure gauges (having a similar device design) DER with unified electrical output signals are widely used, used in control systems, automatic regulation and control of various technological processes.
A significant disadvantage of deformation pressure gauges is hysteresis.
The essence of the phenomenon: the deformable element of the Bourdon tube, subjected to high pressure, will give slightly inflated readings in subsequent measurements. The same applies to the vacuum gauge, which, after pumping to a deep vacuum, will, on the contrary, underestimate the readings. Considering that the vacuum pump system operates in a pressure range from atmospheric to 0.133 Pa (10 V -3 mm Hg), such differences will adversely affect the accuracy of the strain gauge.

To prevent damage to strain gauges due to significant pressure drops in the measuring systems, a tap or valve is provided that turns off the device between measurements.

A Bourdon tube is an elastic element in instrumentation that allows you to control pressures of all levels used in industry. It senses changes in pressure and converts these changes into mechanical movement. A Bourdon tube is usually connected to a pressure gauge, which displays the change in pressure on a graduated scale.

The Bourdon tube is not an independent measuring device, but an auxiliary element that is installed in the measuring device. It allows you to create the pressure difference necessary to measure the flow rate of a liquid, gas or steam. Bourdon tube pressure gauges are the most common measuring instruments due to their low cost, versatility and high reliability.

Made from a variety of metals, including bronze, brass, and stainless steel. The choice of material is determined by the application environment and the level of measured pressure: the higher the pressure, the stronger the material.

Working principle of a Bourdon tube

One end of the C-shaped Bourdon tube is open, the other, called the tip, is closed. The open end is connected to a coupling having an inlet hole inside the tube. The pressure source is connected to the coupling, so the pressure flows from the source through the inlet and into the tube.

When pressure is applied, the Bourdon tube begins to move. Depending on the design of the element and the type of pressure applied, the tube tends to either straighten or curl. True, the displacement of the tip when pressure is applied is insignificant, in most cases it is no more than one centimeter. In this case, the amount of tip displacement is proportional to the amount of applied pressure. The pressure gauge to which the tip is connected converts this small movement of the tip into a needle movement that can be read.

Types of Bourdon tubes

In addition to the C-shaped Bourdon tube, there is a spiral Bourdon tube, the basic structure of which is the same as that of the C-shaped one, except that the tube in this case has the shape of a spiral.

This winding makes it possible to straighten the tube to a greater extent than the C-shaped one. Ultimately, the displacement of the tube tip when pressure is applied is greater than that of a C-tube. Since some instruments require greater displacement than a C-tube, this increase using a spiral tube is considered an advantage.

There is also a Bourdon screw tube, the design of which is very similar to the design of the C-shaped and spiral tubes. One main difference is this: in a helical tube, the turns are wound in a helical manner close to each other. This makes the tube design much more compact than others and can be used in confined spaces. Just like the helix, the helical tube has a greater tip offset compared to the C-tube.

A Bourdon tube pressure gauge is used to measure gauge pressure from 0.6 to 70 bar. It is a mechanical pressure measuring device and operates without power supply.

A Bourdon tube is a ring-shaped tube with an oval cross-section. The pressure of the measured medium acts on the inner surface of the tube and causes movement of the loose end of the tube. This movement is a measurement of pressure and is displayed through a mechanism. This movement is a measure of the amount of pressure and is displayed through a mechanism.