Recoding the remote control for the barrier. How to program the gate remote control

First of all, you need to register the remote control to the receiver on the control board. All gate automation manufacturers have different algorithms for programming remote controls, so there is no single recipe. Let's look at the main manufacturers of gate automation present on the Ukrainian market - Professional (GANT), Came, FAAC, Doorhan, Nice.

First of all, a little educational program.

In systems from Came, FAAC, Nice, one remote control is written to the drive receiver, and then the required number of other key fobs is copied from it. If you try to record the next remote control into the receiver, the first remote control and all remote controls recorded from it will stop working. In cases where you have lost your old remote control, there is no need to delete it from memory - it will be erased itself when you write a new one to the receiver. A huge advantage of such systems is convenience - there is no need to open the cover of the electric drive every time if there is a need to record another remote control. But this system is very vulnerable - I only need to hold your remote control in my hands for 10 seconds to steal a signal to my remote control. And this opens the gates to almost everyone who held your remote control (or the remote control of your employees) in their hands. Let’s say you decide to restrict access to a parking lot, install a barrier and give tenants 20 Came remote controls (equal to the number of parking spaces). But after a couple of weeks there is not enough parking space again. Why? Because employees give each other remote controls for copying, and several times more of them appeared than were issued. You can read how to do this below.

What is the way out? Install a system from Professional (GANT, China) or Doorhan (Dorkhan, Russia). The main difference between such systems is that the signal from each remote control is recorded individually in the receiver. The downside is the limitation on the number of remote controls that can be recorded in the receiver (depending on the model, from 25 to 128 pieces) and the need to open the cover of the drive or receiver each time to record the next remote control. But such a system will not allow clones to be multiplied on the sly. Recommended for businesses and parking lots with a large number of users. You can’t trust all your employee-users without exception, can you? Another advantage is the fact that the remote controls from these manufacturers are also two to three times cheaper than Italian ones.

Remote control Professional - cost 100 UAH

Press the “LEARN” button on the gate drive control unit for 1 second, the “LEARN” LED will light up. Press the button on the key fob, the “LEARN” LED on the control unit will flash and go out. Your keychain has been saved.

If you need to record additional remote controls, repeat this operation. It should be noted that a limited number of remote controls are recorded in the receiver’s memory (depending on the memory capacity of the microcircuit, the number of recorded remote controls can range from 25 to 128 pieces).

To remove all key fobs, you must hold down the “LEARN” button for 8 seconds. All key fobs will be erased from memory.

Came remote - cost 25 Euro

Download instructions

You must press and hold the PROG (CH1) button on the control unit. The LED indicator starts flashing (left figure). Press the required button on the key fob. The LED indicator lights up steadily, indicating successful programming of the control unit (right figure). Release both buttons. The remote control is recorded.

Press and hold both buttons on the remote control you want to program (new remote control) (1). The LED indicator on it will start flashing quickly (2). Release the buttons and press the one you want to program (3). The indicator should light up steadily. In no more than 10 seconds, bring the master key fob (programmed remote control) from below and behind to the programmable one (on which the indicator is lit) and press the operating button (4) once. The LED indicator will flash three times (5) and go off (6). To program other key fobs, repeat the operation. Thus, the automatic system can be configured to work with any number of remote control transmitters with the same code.

FAAC remote control - cost 25 Euro

Download instructions

To record the FAAC remote control into the electric drive receiver, you must simultaneously press two buttons P1 and P2 on the control panel and release them when the indicator on the remote control flashes (after 1-2 seconds). Then press and hold the button on the receiver board - the indicator on the board should blink.

While the remote control indicator is flashing, you must press on the gate control panel the button that needs to be programmed to control the gate leaf. Before releasing the receiver button, make sure that the diode is on for about 2 seconds (to confirm that the code is saved). Now release the button on the remote control and receiver. The remote control is recorded.

But if you want to record more than one remote control, do not try to repeat this operation, since the next remote control (new) will be recorded in the receiver, and the previous one will be deleted. It is necessary to carry out an operation to copy the remote control. See below for how to do this.

On the main remote control (recorded to the receiver), press and hold two buttons P1 and P2 at the same time, release them when the indicator on the remote control flashes (after 1-2 seconds).

Then place the copied (new) remote control opposite the programmed one as shown in the picture above. On the main remote control (while the indicator is flashing), press and hold the button from which you want to rewrite the signal. Now press the button on the new remote that you want to program. The indicator should blink twice to indicate that the code has been saved. Release the button and repeat the operation for other proteins. Thus, the automatic system can be configured to work with any number of remote control transmitters with the same code.

Doorhan remote control - cost 20 Euro

Download instructions

Before starting programming, it is recommended to clear the receiver’s memory of previously recorded remote control codes. To do this, after turning on the power, hold down the record button on the remote control for 10 seconds. The LED will blink for 10 seconds, then go out for 2 seconds and blink twice again to confirm that the stored remote control codes have been erased.

To record the remote control into the receiver, press and hold the remote control recording button on the radio receiver board for 3 seconds - the LED1 indicator on the receiver will light up. After this, press the required button on the remote control for 2-3 seconds. To configure multiple remotes, repeat the procedure for other remotes.

Nice remote control - cost 25 Euro

Download instructions for remote controls with dynamic code

NICE remote controls come in two types - constant code (blue body) and dynamic code (black body)

Programming the Nice Flo remote control with a permanent code is done by setting two-position dip switches, both in the remote control itself and in the radio channel. Be careful - the variations must match. If you need an additional remote, simply unwind the old programmed Flo remote and set the switches to the same position. These are old-style remote controls, very rare today. Therefore, we will dwell in more detail on programming remote controls with dynamic code.

On the receiver, press the key once (delay less than 1 second). Press and hold the button on the remote control for 3-4 seconds, after which the indicator on the receiver will blink 3 times. This means that the remote control has been successfully recognized and recorded in the receiver. After this, the receiver will be in programming mode for another 10 seconds, during this time,

If necessary, you can record several more remote controls. After the time has expired (10 seconds), the receiver will remember all the remote controls assigned to it and all the buttons on each remote control.

You can also program the remote control remotely, using a previously recorded remote control. As a result, the button on the “new” remote control will copy the command from the button on the “old” remote control. ATTENTION! Programming a new remote control from an old one must occur within the range of the receiver

Press the desired button on the new remote control for 5 seconds, then release. Press (without holding) the button on the old remote control 3 times. On the new remote control, press the same button 1 time and release. The remote control button is recorded and performs the same commands as the old remote control button.

Remote controls stored in the receiver's memory can be deleted if necessary. To do this, you need to carry out the following operations:

Press and hold the button on the receiver, You need to wait until the LED lights up 1 time, goes out 1 time, and then flashes 3 times, Release the button at the third LED flash.

If all operations are carried out correctly, then after a short pause the LED on the receiver will flash 5 times.

It is one of the best on the world market. Thanks to their precise automation, life becomes convenient and comfortable, as well as safer. Came devices are available, there are no problems when installing on any gate, and there is no need to change them, which saves you a lot of money.

As for climatic conditions, it should be noted that manufacturers approached this issue responsibly. The equipment can withstand frost, wind, heat, dust and rain.

Remote controls from CAME

TOP-432NA is the most popular. Due to the fact that it is two-channel, you can control a separate device, for example, open a barrier and gate. Frequency 433.92 MHz. Manufactured using permanent code technology. Size -32x68x13. Works at a distance of up to 150 meters.

Programming

1. It is necessary to set the distance no more than 5mm from each other.

2. Press two buttons simultaneously on the new remote control and hold them. The indicator flashes rapidly.

3. Release the button and press the one that needs to be programmed. Now the indicator lights up smoothly and does not blink.

4. Quickly turn on the key on the old key fob that will be used for overwriting. All this must be done while the light on the new remote control is on.

5. If everything is done correctly, then the indicator on the “clean” key fob will blink three times. This indicates that the recording was successful, that is, the code has been rewritten.

TOP-432SA - two-channel, works on two devices. Frequency 433.92 MHz.

Copy

1. The distance between key fobs should be no more than 5mm.

2. On the new one, press and hold the button that will be used to record until the indicator lights up evenly.

3. When the button on the new remote control lights up, you need to press on the other one, from which the code will be rewritten.

4. The remote control should blink three times. Everything was done correctly.

TOP-434NA – Four-channel key fob with an operating frequency of 433.92 MHz.

Programming Came TOP-434NA

1. You need to press and hold two buttons simultaneously on the new key fob until the blinking changes.

2. The lamp burns evenly. You need to briefly press the button on which the code will be written.

3. While the indicator on the first one is lit, you must quickly press the key on the second one with which you want to rewrite the code.

4. The new key fob should blink three times, indicating a successful result.

TOP-432EE is a new model of the TOP series. It works in two encoding systems TAM and TOP, which allows you to work with remote controls at those facilities where the TOP and TAM encoding was installed.

Programming with TOP-432NA

1. Preparation for programming. Press and hold the button on the first key fob transmitter that needs to be programmed until the indicator starts flashing. Release them on the new remote.

2. Click on the button. The indicator should light up without blinking.

3. Within ten seconds, you need to bring the key fob to the TOP-432NA, on which the light is on. Turn on the button on the master key fob once. The LED will blink three times and go out, indicating that copying has been successfully completed.

TOP-432EV is an improved model of the TOP series. Contains 4096 code operations. 32x69x11 mm – overall dimensions.

Copying Came TOP-432EV key fob from TOP-432NA

1. Press and then hold the top two buttons on the key fob you want to program until the indicator starts blinking quickly. Now you need to release two buttons on the TOP-432NA remote control.

2. You need to press any key that you will program.

3. The light should burn evenly.

4. Within ten seconds, bring the TOP-432EV key fob from below and behind to the TOP-432NA, where the indicator lights up, press the TOP-432NA operating button once. The remote device is ready for operation when the light blinks three times.

Remote controls are new products from Came, which are designed to protect the radio control code from illegal copying by outsiders. Available in two-button and four-button. Radio key fobs with dynamic code system.

Programming Came Twin remotes

1. You must have an already authorized key fob that has already been entered into the system using the receiver button.

4. Within twenty seconds, press the button on the new key fob once.

5. We wait about twenty seconds until the radio receiver exits the so-called programming mode.

6. New code has been entered. This procedure can be done with the following remote control. But it is very important: one radio receiver supports no more than 25 key fobs. Also turn off those receivers that are close, into which you do not need to enter a new code.

Came TCH-4024 and TCH-4048 are four-channel and eight-channel transmitters with a frequency of 40 MHz. Touch is a new generation sensor that allows you to control multiple objects. There is protection against accidental key presses.

Copying Came Touch Remotes

1. Press and hold the top two buttons at the same time until the indicator starts flashing faster.

2. Click the button you want to activate. The indicator will glow steadily.

3. Bring the working key fob from behind to the new one for ten seconds and press the (working) button and hold for a few seconds.

4. The indicator should blink three times if everything was completed without errors.

Came and – two-channel and four-channel with rolling code. Atomo is a convenient, sleek remote that ensures excellent performance for customers. Ensures the reliability of the outgoing signal.

Programming Came Atomo remotes

1. Select an area of ​​excellent reception, no further than five meters.

2. On a working key fob, press and hold the button until the indicator lights up steadily for about fifteen seconds.

3. On a new device, hold the button once for about twenty seconds.

4. We wait fifteen seconds and check the operation of the new key fob.

Nice

Engaged in the production of automated systems for gates, barriers and doors. This Italian company occupies a leading position in the world of automation. Nice products are reliable, high quality, time-tested.

The ability to control all processes (close gates, open blinds) with one remote control, without leaving your home.

Nice FLO 1, FLO 2, FLO 4 – remote control with dynamic code. Frequency 433.92 MHz. Response range up to 150 meters. Dimensions 72x40x15. They produce single-channel, two-channel, four-channel.

Remote controls Nice FLOR 1S, FLOR 2S, FLOR 4S. Single-channel, two-channel, and four-channel models are available. Range of action – 150-200 meters.

Programming Nice FLO, FLOR

1. There must be a receiver nearby.

2. Remote controls must be located in sequence.

3. Press any button on the new one and hold it for about five seconds.

4. Press the button on the old remote control three times.

5. Now on the new one we press once the button that we already pressed at first and release it.

Nice ON 1, ON 2, ON 4, ON 9 - remote controls with dynamic code. Elegant appearance, small dimensions. Works in all weather conditions. There is a special ring for attaching to keys. Control frequency 433 MHz.

Programming Nice ON remote controls

1. The two remote controls must be touching at the top.

2. Press any button on the new key fob and hold it until the light on the old one lights up. We release the key, and the indicator on the second one should blink.

3. Press any button on the old key fob and hold the button on the new one until the indicator lights up.

4. Release the button on the old key fob. The indicator on the new one goes out - this means programming has been successfully completed.

Nice Very VE is a two-channel remote control with a statistical code.

Programming Nice Very VE

1. Press two buttons simultaneously until the light remains on.

2. Press the top key if the first switch on the receiver is in the “On” position. Press the bottom button if the microswitch is in the “Off” position.

3. We repeat point No. 2 for all ten microswitches that are located on the receiver.

4. The LED will start blinking quickly if the tenth switch is turned on. While it is flashing, if no buttons are pressed, then the code will be stored in memory.

Nice Very VR is a two-channel key fob with a floating code. Frequency 433.92 MHz.

Programming the Nice Veri VR remote control

1. There must be a remote control that is already recorded in the receiver. The first one is always written to the rolling code receiver using the receiver button.

2. Within five minutes, transfer the code by holding the key on the new remote control.

3. Press the button of the old device three times

4. Briefly press the button on the new remote control. All recording is completed.

Hormann – time-tested quality

Products of Germany. Reliability, convenience, beautiful design.

This manufacturer produces remote controls with the same design, but with different radio frequencies. The buttons differ in color: blue (868 MHz), green (26, 975 MHz), gray (40 MHz).

Hormann HSM 4 – four-channel remote control for gates and barriers. Overall size 37x110x13. Frequency 868 MHz. Dynamic code.

Programming the HSM 4 remote control

1. Place the keychains head to head.

2. Press the button on the old remote control and hold it. The light should be on constantly.

3. Press and hold the programming key on the new remote control. The light will flash slowly for about four seconds at first and then flash faster once successful.

The HSE2 remote control is two-button. Key ring. Frequency 868 MHz.

Hormann HSM with a frequency of 40.680 MHz. Two-button and four-button.

Programming Hormann HSM 40 MHz

1. Place the new remote control next to the old one.

2. Press the button on the old remote control and hold it.

3. Press the corresponding button on the new remote control. The LED should blink four times.

4. Release the buttons.

HSP4-C – remote control for gates and barriers. New design. Beautiful appearance. Frequency 868 MHz. Dimensions – 48x48x13 mm. The number of buttons is four.

Copying the HSP4-C remote control

1. Place the key rings next to each other.

2. Press the transmitter key that inherits the code and hold it for five seconds. The indicator should be lit constantly.

3. Then press the button that needs to be programmed on the new key fob and hold it. The light will blink slowly for about four seconds, but will blink faster after the task has been successfully completed.

4. Release the keys on both remote controls.

Doorhan

The Doorhan company is a large Russian supplier of automation for gates, remote controls, and radios. Focuses on the global market.

Doorhan Transmitter 2, Transmitter 4 – remote controls with dynamic code. Operating frequency 433 MHz. Designed for remote control of two and four automatic Doorhan devices, as well as any other automation with an existing Doorhan radio. One key fob can control two (four) gates and barriers.

Programming Doorhan remote controls with DHRE-2 receiver

1. Clear the memory of old codes. After turning on the power, hold down the record button on the remote control for about 10 seconds. The indicator will blink for 10 seconds, then go off, then blink twice. All old codes have been removed.

2. To write down the remote control code, press and hold the “SW1” key on the receiver board for 3 seconds. Then press the button on the remote control for 2-3 seconds.

3. If settings for other remote controls are required, then the code is recorded again.

You can program a specific control channel with each key.

BFT products guarantee quality and reliability

VFT -12, VFT -12 – two-channel, four-channel remote controls. Frequency 433.92 MHz.

Programming BFT remote controls

1. Click the “Ok” button. A greeting message will appear.

2. Click the “Ok” button. We see the first section of the “PARAMETER” menu.

3. Now press the “-” key several times, the “RADIO” menu appears.

4. Click “Ok” again and see that the menu section for adding key fobs to the radio receiver’s memory “AD start” appears.

To add key fobs you need:

1. Press the “Ok” button - the message “hidden button” appears.

2. Press the two key fob buttons that need to be recorded.

3. “Release” will appear, followed by “desired button”.

4. Press the remote control button.

5. “Ok 1” appears. Everything went well.

6. To record other key fobs, we will do everything by analogy.

7. After all remote controls have been recorded, press the buttons twice<+>And<->simultaneously.

Faac is a recognized market leader in the production of automatic barriers and gates

The Italian company is known not only in Europe, but throughout the world.

XT2-868 SLH, XT4-868 SLH – two-channel and four-channel remote control for gates and barriers with 868.35 MHz frequency. Operates at temperatures from -20 to +55 C. Radius up to 50 meters.

FAAC DL2 868 SLH, FAAC DL4 868 SLH - obsolete models, discontinued. Two-channel and four-channel. The new XT series remotes completely replace the previous ones. They differ only in stylish design and improved characteristics.

Programming FAAC XT2-868 SLH and XT4-868 SLH series remote controls

You need a master key fob, that is, the one that was recorded first (master), as well as a new remote control (slave).

1. Press the P1 and P2 buttons on the old device for two seconds at once. The LED blinked, then programming can begin, since it saw this device.

3. The indicator is constantly on. Press the key on the old remote control that you want to overwrite.

4. Press the button on the slave remote control for programming. Release the button after the light blinks twice.

5. All copying is complete. Actions can be performed on all other buttons and other remote controls.

In conclusion, I would like to say that now in our time an automatic control system is installed on all types of barriers, gates, and doors. You can control it using a separate remote control, which greatly increases the level of security, especially against theft.

Using the automatic remote control is a pleasure. The main thing is that you can always carry it with you on a keychain. You can also use it, for example, in bad weather without leaving your home. Everything can be selected and installed according to the client’s wishes.

We thank you for purchasing the CHANGER universal programmable remote control and hope that you will be satisfied with the performance of our remote controls.

To program the remote control, you will need a miniUSB cable, which can be purchased at any computer store, or you may already have one (currently this connector is quite widely used in phones and other devices of various brands). Before using the remote control, we strongly recommend that you follow all instructions step by step.

Remote control programming instructions

Download the latest version of the program installer. Run the installer. Select the installation folder and other options. For correct operation of the program, it is recommended to agree with all options of the program installer.
Programming the remote control must be carried out with the batteries installed.

The first thing you need to do is find the desired remote control and determine what type of ChangerUSB it is in. And connect this particular type of Changer for firmware.

This is the main thing you need to understand in programming. I'll tell you how to do it. Select the firmware by highlighting it with the cursor. We move on to the next window located in the middle of the program and determine the type of remote control (Changer) for the firmware. To do this, we sort through the devices, from top to bottom.

If you have selected the device correctly, something like the following figure should appear. Button name or button ID.

After this has been found out, you need to connect exactly the same Changer as in the program figure, where the button IDs and names appear.

At the bottom of the RCCreator program window there are two connection status indicators: on the left - the remote control, on the right - the signal receiver. Before you start working with the program, make sure that the icon of the device you are connecting lights up green.

If the type of firmware and the connected remote control are selected correctly, the button to program the remote control becomes active. Click (Program the remote control)

Press (+) to start programming:

The red LED on the remote control lights up, which means the programming process has begun. After the diode goes out, the programming process is completed. The programming tab will show the data of the recorded remote control. After completing the programming process, close the programming window and only then disconnect the remote control from the miniUSB cord.

All that remains is to print the instructions by clicking on the Printer icon in the program. All. The remote control is ready to control the device for which it was programmed.

Service capabilities of the program

AUTOMATIC SEARCH - under development

SEARCH BY BUTTONS is a search for interchangeable remote controls that have the same signal, both from the same manufacturer and from others, in a similar or different type of remote control housing. Open the search tab, remove the “POWER” button signal from the remote control, the button signal will be displayed digitally at the top left of the tab. press the “POWER” button in the “SEARCH” tab, a list of remote controls that match the signals of the “POWER” button will be displayed on the left. It is recommended to use the signals of the following buttons for searching - “POWER, 1, VOL +, CH +, OK, MENU”.

SEARCH BY PROTOCOL is a search using signals from remote control buttons that are not in the “SEARCH” tab. there are 2 buttons for this […], the search process is similar to searching by buttons.

SEARCH BY BUTTONS AND PROTOCOL OF A REMOTE AVAILABLE IN THE DATABASE - used when the remote control is already in the program database, and you need to select either an analogue or compare it with another remote control available in the database. select the desired remote control in the program, highlight the desired button with the mouse so that on the CHANGER remote control on the right it becomes active and its numerical value is displayed in the signal indicator field. Open the "SEARCH" tab and paste it into the desired button. A list of analogues will be displayed on the left side of the program.

Before you start removing codes from remote controls for the first time, we recommend that you read the instructions, which can be found through the “About the program” - “Help” menu.

We also recommend that you familiarize yourself with the information provided below:
After the codes of all buttons are written down, it is better to close the program through the “exit” or “cross” in the upper right corner - the information is saved when closing. The program may close with an error, resulting in the loss of the last entered data.

To be more confident in the safety of the remote controls you removed, we recommend exporting the codes to a separate folder. To do this, create, for example, a folder named “DRC” in any convenient place. After removing the remote control codes, select “File” - “Export” and specify the folder you created. For additional data protection, just in case, we highly recommend regularly making a backup copy of removed remote controls to other media. We would be very grateful if you would send the removed remote controls to our email address. Those who are especially active will receive additional discounts on remote controls.

Turn on the device you will be controlling. Brand code search is only supported on older TVs, DVD players, VCRs and satellite receivers. It is not supported by stereo systems, digital video recorders, or high-definition televisions (for these devices, use the other method described in this article).

• The brand code can be found in the documentation for the remote control or on this website.